Tensile fracture of as-cast and hot rolled Mg-Zn-Y alloy with
long-period stacking phase
WANG Bai-shu(王柏树)1, 2, XIONG Shou-mei(熊守美)1, LIU Yong-bing(刘勇兵)3
1. State Key Laboratory of Automotive Safety and Energy, Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China;
2. Key Laboratory of Advanced Structural Materials, Ministry of Education,Department of Materials Science and Engineering, Changchun University of Technology, Changchun 130012, China;
3. Key Laboratory of Automobile Materials, Ministry of Education, Department of Materials Science and Engineering, Jilin University, Changchun 130025, China
Received 23 September 2009; accepted 30 January 2010
Abstract: An experimental Mg97Zn1Y2 (molar fraction, %) alloy was produced by rolling the as-cast alloy. The microstructure of the alloy is composed of the α-Mg (also marked as 2H-Mg with reference to long-period stacking structure according to hexagonal close packed structure) and long-period stacking (LPS) phase. Tensile tests of Mg97Zn1Y2 alloy in comparison with pure Mg were conducted. The fracture morphologies of the tensile specimens were characterized and the microstructures near fracture surface were observed. The results show that the rolled Mg97Zn1Y2 alloy shows a mixed fracture mode including dimples indicating a ductile fracture pattern and a small fraction of cleavage planes indicating a brittle fracture pattern, which is different from the single brittle fracture of the as-cast alloy. In addition, the plastic deformation is mainly from dislocations induced strain with small strengthening effect during plastic deformation in the as-cast Mg97Zn1Y2 alloy, and the strain hardening rate is similar to that of the as-cast pure magnesium. The deformation mechanism of Mg97Zn1Y2 alloy is different from that of the pure magnesium according to a metallographical observation that whether twins are found or not. The strengthening effect hardly exists in the rolled Mg97Zn1Y2 alloy under the same dislocations induced strain, which is different from that of the as-cast alloy with moderate strengthening effect.
Key words: magnesium-yttrium-zinc alloy; long-period stacking phase, rolling; mechanical properties; fracture
1 Introduction
Due to strong demand for mass reduction of transportation vehicles for better fuel efficiency, magnesium alloys have recently received much research interest in applications to various structural components of automobile and aircraft industries[1]. Inter-metallic phases can be found in almost every magnesium alloy and play a very important role in optimizing micro- structure and mechanical properties[2]. Mg-Zn-RE-Zr system is regarded as a high strength magnesium alloy system because of evident strengthening effect of rare earth (RE) addition on magnesium alloys. PADEZHNOVA et al[3] found X-Mg12ZnY (molar fraction, %) as ternary equilibrium phase. LUO et al[4-5] identified X-Mg12ZnY phase as an 18R long-period stacking (LPS) structure by electron diffraction technique. KAWAMURA et al[6-8] fabricated a high strength Mg-based Mg97Zn1Y2 alloy with a novel LPS structure by rapid solidification (RS) techniques such as powder metallurgy and melt-spinning, and variation and formation process of LPS structures were reported later[9-11]. Since the strength of conventionally cast Mg97Zn1Y2 alloy is lower than that of commercial AZ91 at room temperature, investigations to improve the properties of Mg alloys with LPS structure as second phase were focused on refining the LPS structure or applying deformation treatment[12-13]. While the tensile strength and fracture characteristics of Mg97Zn1Y2 alloy, as one of the promising engineering magnesium alloys, have not been reported clearly. In the current work, tensile tests of the as-cast and the rolled Mg97Zn1Y2 alloys were conducted and the results werecompared with those of the as-cast and rolled pure magnesium.
2 Experimental
The nominal composition of the alloy was Mg97Zn1Y2 (molar fraction, %) in this study. The experimental conditions such as the casting and the hot-rolling process parameters can be obtained by referring to our previous work[14]. The ingot was prepared by melting Mg-19.9%Y (mass fraction) master alloy and pure magnesium in a graphite crucible at 775 ?C with protecting atmosphere of SF6+CO2 gas mixture, and adding pure zinc particles after melting completely and holding at 775 ?C for 30 min, and then casting the alloy into a steel mould of 190 mm× 95 mm×20 mm. Plate type samples for rolling were cut from the ingot. The samples for deformation were heat-treated at 400 ?C for 30 min before rolling. The thickness of the plates after nine-pass hot-rolling was reduced by 74.8% at 12%-17% deformation strain per pass. All rolled specimens were etched with acetic-picric acid solution (5.5 mL CH3COOH, 2.1 g picric acid, 5 mL water, 2 mL nitric acid and 90 mL alcohol). The tensile specimens were prepared from the as-cast and the rolled materials and the tensile axis of the rolled materials was kept to be along the rolling direction. The gauge size was 4 mm in width, 1 mm in thickness and 10 mm in length. Tensile tests were performed on an Instron tensile test machine at a strain rate of 6.7×10-4 s-1. The fracture morphologies of tensile specimens were characterized using a scanning electron microscope (JSM5600, JEOL). The microstructures near fracture surface were observed by a laser optical microscope.
2.1 Microstructure of as-cast and hot-rolled Mg97Zn1Y2 alloy
The microstructures of the as-cast and hot rolled Mg97Zn1Y2 alloys were studied[14]. The microstructure of the as-cast Mg97Zn1Y2 alloy consists of α-Mg dendrites and the X-Mg12ZnY phase. Besides the eutectic LPS phases on grain boundaries, part of which are devoiced eutectic phases, there are some fine acicular phases within the α-Mg phase and near grain boundaries which are precipitated from α-Mg along basal planes during cooling.
The deformation texture of the Mg97Zn1Y2 alloy after hot rolling can be observed to be along rolling direction as presented in Ref.[15]. No deformation twins are found and deformation bands can nearly be visible after hot rolling. The existing weak contrast in the deformation microstructure confirms that the partial recrystallization behavior and the extended recovery occur during cooling after hot rolling at an elevated temperature of 400 ?C in the α-Mg matrix. The recrystallized grains are difficult to be identified because of small orientation difference between them.
2.2 Tensile test curves
The graphs of true stress—true strain obtained from tensile test are shown in Fig.1. The yield strengths of as-cast and rolled pure magnesium specimens are 18 and 108 MPa and those of Mg97Zn1Y2 alloys are 85 and 282 MPa, respectively. The strengthening effect of as-cast Mg97Zn1Y2 alloy with the LPS phase is significantly obvious in comparison with the as-cast pure magnesium. The working hardening resulting from the rolling deformation is different for pure magnesium and Mg97Zn1Y2 alloy. The elongation prior to ultimate rupture of Mg97Zn1Y2 alloy is lower than that of pure magnesium. The elongation of rolled Mg97Zn1Y2 alloy presented in Fig.1 is slightly larger than that of the as-cast alloy.
Fig.1 True stress—true strain curves of as-cast and rolled pure magnesium and Mg97Zn1Y2 alloy in uniaxial tensile test at room temperature
2.3 Fracture morphologies
The fracture morphologies of the tensile specimens from as-cast and rolled pure magnesium and Mg97Zn1Y2 alloy are shown in Fig.2. The fracture of the as-cast pure Mg is composed of two grain boundaries and cleavage planes. Therefore, a mixed brittle pattern of trans- granular and inter-granular cleavage fractures is its fracture mode (as shown in Fig.2(a)). The fracture of the rolled pure Mg is made up of tear ridges and vein pattern as shown in Fig.2 (b) and the fracture mode is almost trans-granular brittle pattern. Fig.2(c) shows the fracture characteristics of the as-cast Mg97Zn1Y2 alloy, which can be described as a brittle quasi-cleavage mode including mainly cleavage planes from 2H-Mg phase and inter-granular interfaces between the 2H-Mg and 18R X-Mg12ZnY phases. The fracture of rolled Mg97Zn1Y2 alloy is mainly characterized by dimples, a shear angle existing from the midline of the sample to two surfaces of RD-TD section and localized tear ridges as shown in Fig.2(d), which indicates a ductile fracture mode attached by cleavage fracture.
2.4 Microstructures near fracture
The microstructures of all tensile samples are shown in Fig.3. There are many big primary twins in the as-cast pure magnesium, which are originated from the grain boundaries and extend to the interior of grains, and some secondary twins inside the primary twins as shown in Fig.3(a) and the inset image. Twins occur more severely on grain boundary than within the interior, thus a crack initiates on the grain boundary and even develops along it. The fracture is judged to originate from the grain boundary indicated by fine recrystallization grains which may be obtained by recrystallization during processing into the inset samples at 150 ?C. Fig.3(b) shows that the
Fig.2 Fracture images of as-cast and rolled pure magnesium and Mg97Zn1Y2 alloy using SEM: (a) As-cast pure magnesium; (b) Rolled pure magnesium; (c) As-cast Mg97Zn1Y2 alloy; (d) Rolled Mg97Zn1Y2 alloy
Fig.3 LOM micrographs including inset images near fracture of as-cast and rolled pure magnesium and Mg97Zn1Y2 alloy by uniaxial tensile test (at TD-RD section of deformation samples): (a) As-cast pure magnesium; (b) Rolled pure magnesium; (c) As-cast Mg97Zn1Y2 alloy; (d) Rolled Mg97Zn1Y2 alloy with one inset image from a 3D LOM micrograph at ND-RD section
fracture of the rolled pure magnesium travels whether among the very fine recrystallized grains or along deformation bands. Twins are hardly found in the hot worked samples, and it can be understood as follows. The tensile strain comes from movement of dislocations within shear bands of deformation texture during nine passes of thermo- machining at 400 ?C in which other slip systems than basal plane slide are activated and the mechanical twins are suppressed by refined grains and dense shear deformation bands. In Fig.3(c), the final fracture is ended by a shear angle near fringes of the sample. In case of the rolled Mg97Zn1Y2 alloy, as shown in Fig.3(d), the neck prior to rupture occurs during tensile test based on the deformation texture. While a straight fracture in the transverse direction is imposed nearly with zigzag.
3 Discussion
When tensile test is conducted on a dual-phase or multi-phase alloy, crack initiation generally occurs at the phase interfaces. This is different from the crack initiation resulting from deformation twins in the as-cast pure magnesium. In case of the as-cast Mg97Zn1Y2, the crack initiates at the interfaces between α-Mg and X-Mg12ZnY, which is judged by different deformation mechanisms of two phases though they have an orientation relationship of aLPS//a2H, bLPS//b2H and cLPS// c2H[5]. In addition, the dislocation types are different for α-Mg grains with or without LPS phases[16]. The fracture mode of as-cast Mg97Zn1Y2 alloy is a quasi- cleavage pattern with cleavage plane across 2H-Mg grains and inter-granular pattern between two HCP structures as shown in Fig.2(c). Furthermore, twins are not visible for as-cast Mg97Zn1Y2 alloy as shown in Fig.3(a). MATSUDA et al[17] pointed out that the LPS phase contributed strengthening effect to the as-cast Mg97Zn1Y2 alloy and the twins were deflected or arrested in the region with high density of bundled LPS phases. In comparison with the tensile profile of the pure magnesium, the hardening effect induced by mechanical twins is not marked. A yield strength of 85 MPa is due to the mechanism of the second phase strengthening in as-cast Mg97Zn1Y2 alloy, and the strain hardening of the as-cast Mg97Zn1Y2 alloy in Fig.1 during tensile test is mainly from dislocation multiplication.
The fracture of the rolled pure Mg is mainly made up of vein pattern because of the hard orientation resulting from rolling. While, when the tensile test was performed upon rolled Mg97Zn1Y2 alloy, a mixed fracture morphology including dimples, tear ridges and cleavage planes can be observed in Fig.2(d). The size of localized cleavage plane regions is much bigger than that of dimples, which is below 10 μm usually, and almost equal to that of the grains of as-cast alloy, which is about 30 μm. The mean grain size of rolled alloy at normal direction is about 6 μm according to the inset 3D LOM images of Fig.3(d), which is close to the size of above mentioned dimples. The deformation texture of the rolled Mg97Zn1Y2 alloy can be observed clearly in Fig.3(d). The existence of cleavage planes and dimples shows the inhomogeneity of rolling strain in this experiment in connection with developed recovery and partial recrystallization in 2H-Mg. The dimples can be understood as that recrystallization grains or deformation substructures below 10 μm rotate its orientation to accommodate further strain in order to obtain a uniform strain in a whole grain. Of course, the α-Mg dendrites as matrix in the as-cast Mg97Zn1Y2 alloy is believed to be a Mg-Y binary alloy, in which elevating deformation temperature and increasing yttrium content can reduce the effect of twins as a deformation mode and increase the activity of non-basal slip mode[18]. The addition of high level of yttrium combined with a high deformation temperature up to 400 ?C leads to a near random distribution of dynamically recrystallized grains in contrast to strongly textured parent grains. The LPS phase is fragmented during rolling and its dissolution resulting from the reaction with deformation defects such as dislocations leads to precipitation at grain boundaries and in the cell wall of substructure. The dimples would develop from small second phase particles. Thus, the mechanism of ductile fracture is explained. The neck prior to rupture exists in tensile test rests from the ductile mode of fracture. The big α-Mg grains are difficult to randomly shift their orientation to accommodate the same strain as that of very small grains, therefore a localized cleavage plane indicating brittle fracture also occurs during tensile test in rolled Mg97Zn1Y2 alloy. From Fig.1, a balance between strain hardening and strain softening is maintained before fracture and the curve of rolled Mg97Zn1Y2 alloy is much smoother than that of the as-cast Mg97Zn1Y2 alloy, which indicates that the dislocations generated by rolling are activated and started up, and that annihilation and occurrence of dislocations at grain boundaries keep balance until rupture. After deformation, the tensile strength at room temperature is upgraded from 85 MPa to 282 MPa and the mechanisms of strengthening are derived from deformation texture and grain refinement strengthening.
4 Conclusions
1) In as-cast Mg97Zn1Y2 alloy, the fracture is originated from phase interface and developed by cleavage planes across the α-Mg grains. A brittle fracture mode is obtained, which is similar to the mixed brittle fracture mode of the inter-granular and the trans-granular patterns in as-cast pure magnesium.
2) In rolled Mg97Zn1Y2 alloy, dimples, localized cleavage planes and tear ridges indicate a ductile mixed fracture mode, which is different from the single brittle fracture of the as-cast alloy and the rolled pure magnesium.
3) The deformation mechanism during tensile test is changed from mechanical twins induced strain with obvious strengthening effect in the as-cast pure magnesium to the strain with slight strengthening in the rolled metal which is jointly induced by the dislocation movement and partial mechanical twins, to dislocations functionally induced strain in the as-cast Mg97Zn1Y2 alloy, and to dislocations induced strain without remarkable strengthening effect in the rolled alloy.
References
[1] Mordike B L, Ebert T. Magnesium: Properties- applications-potential [J]. Materials Science Engineering A, 2001, 302(1): 37-45.
[2] Hort N, Huang Y D, Kainer K U. Intermetallics in magnesium alloys [J]. Advanced Engineering Materials, 2006, 8(4): 235-240.
[3] Padezhnova E M, Melnik E V, Miliyevskiy R A, Dobatkina T V, Kinzhibalo V V. Investigation of the Mg-Zn-Y system [J]. Russian Metallurgy (Metally) (Engl Transl), 1982, 4(9): 185-188.
[4] Luo Z P, Zhang S Q, Tang Y L, Zhao D S. Comments on the so-called Z-phase in magnesium alloys containing zinc and rare-earth elements [J]. Journal of Alloys and Compounds, 1994(1/2), 209: 275-278.
[5] Luo Z P, Zhang S Q. High-resolution electron microscopy on the X-Mg12ZnY phase in a high-strength Mg-Zn-Zr-Y magnesium alloy [J]. Journal of Materials Science Letters, 2000, 19(9): 813-815.
[6] Kawamura Y, Hayashi K, Inoue A, Masumoto T. Rapidly solidified powder metallurgy Mg97Zn1Y2 alloys with excellent tensile yield strength above 600 MPa [J]. Materials Transaction, 2001, 42(7): 1172-1176.
[7] Inoue A, Kawamura Y, Matsushita M, Hayashi K, Koike J. Novel hexagonal structure and ultrahigh strength of magnesium solid solution in the Mg-Zn-Y system [J]. Journal of Materials Research, 2001, 16(7): 1894-1900.
[8] Inoue A, Matsushita M, Kawamura Y, Amiya K, Hayashi K, Koike J. Novel hexagonal structure of ultra-high strength magnesium-based alloys [J]. Materials Transaction, 2002, 43(3): 580-584.
[9] Amiya K, Ohsuna T, Inoue A. Long-period hexagonal structures in melt-spun Mg97Ln2Zn1 (Ln=Lanthanide metal) alloys [J]. Materials Transaction, 2003, 44(10): 2151-2156.
[10] Nishida M, Kawamura Y, Yamamuro T. Formation process of unique microstructure in rapidly solidified Mg97Zn1Y2 alloy [J]. Materials Science Engineering A, 2004, 375/377: 1217-1223.
[11] Matsuda M, Ii S, Kawamura Y, Ikuhara Y, Nishida M. Variation of long-period stacking order structures in rapidly solidified [J]. Materials Science Engineering A, 2005, 393(1/2): 269-274.
[12] Zhu Y M, Morton A J, Nie J F. Improvement in the age-hardening response of Mg-Y-Zn alloys by Ag additions [J]. Script Materialia, 2008, 58(7): 525-528.
[13] Watanabe H, Somekawa H, Higashi K. Fine-grain processing by equal channel angular extrusion of rapidly quenched bulk Mg-Y-Zn alloy [J]. Journal of Materials Research, 2005, 20(1): 93-101.
[14] Wang B S, Liu Y B, An J, Li R G, Su Z G, Cao Z Y. The morphological evolutions of LPS phase in the cast and melt-Spun Mg97Zn1Y2 alloy upon deformation and heat-treating [J]. Transactions of Nonferrous Metals Society of China, 2008, 18: s69-s75.
[15] Wang B S, Liu Y B, Su Z G, Cao Z Y. Microstructure evolution in the rolled Mg97Zn1Y2 alloy with long-period stacking phase upon annealing[J]. Materials Transactions, 2009, 50 (2): 261-265.
[16] Matsuda M, Ando S, Nishida M. Dislocation structure in rapidly solidified alloy with period stacking order phase [J]. Materials Transaction, 2005, 46(2): 361-364.
[17] Matsuda M, Ii S, Kawamura Y, Ikuhara Y, Nishida M. Interaction between long period stacking order phase and deformation twin in rapidly solidified Mg97Zn1Y2 alloy [J]. Materials Science Engineering A, 2004, 386(1/2): 447-452.
[18] Cottam R, Robson J, Lorimer G, Davis B. Dynamic recrystallization of Mg and Mg-Y alloys: Crystallographic texture development [J]. Materials Science and Engineering A, 2008, 485(1/2): 375-382.
(Edited by CHEN Can-hua)
Foundation item: Project(2009AA03Z114) supported by the National High-tech Research and Development Program of China
Corresponding author: WANG Bai-shu; Tel: +86-10-62789448, +86-13069138863; Fax: +86-10-62773793; E-mail: baishu6933@163.com