共搜索到18619条信息,每页显示10条信息,共1862页。用时:0小时0分0秒296毫秒
. The strengthening of the micro-alloyed Al-Mg alloys is attributed to the precipitation strengthening by the Al3Sc particles and to the substructure strengthening. Key words: Al-Mg alloy; Al-Mg-Mn-Sc alloy...) and (d)), where it is the finest in alloy D. This suggests that addition of Mn or Sc could retard recrystallization of the Al-Mg alloys during hot-rolling, and the retarding effect is the best when Sc......
The Strengthening of Cu-15Ni-8Sn Alloy WANG Ming-Pu1,WANG Yan-hui1,HONG Bin1 (1.School of Material Science and Engineering, Central South University, Changsha China) 摘要:The microstructure, property and relation between them of Cu-15Ni-8Sn alloy are studied by means of TEM and the measurement of hardness. The results show that γ '' metastable phase strengthens alloy because of its ordering......
The Technological Improvements of Aluminum Alloy Coloring by Electrolysis LI Nai-jun1 (1.Teachers College, Shenyang University, Shenyang 110015, P. R. China) 摘要:The technological process of coloring golden-tawny on aluminum alloy by electrolysis was improved in this paper. The optimum composition of electrolyte was found, the conditions of deposition and anodic oxidation by electrolysis were......
Microstructure and Performances of Nanocrystalline Zinc-nickel Alloy Coatings LI Guang-yu1,NIU Li-yuan1,JIANG Zhong-hao1,LIAN Jian-she1 (1.The Key Lab of Automobile Materials, Ministry of Education, China, College of Materials Science and Engineering, Jilin University, Nanling Campus, Changchun, 130025, China) 摘要:Nanocrystalline zinc-nickel alloy coatings were deposited from an alkaline......
Alloy 20不锈钢薄板等离子弧焊接工艺研究赵斌,王宾宾,王小华中国船舶重工集团公司第七二五研究所摘 要:对Alloy 20不锈钢薄板进行了等离子弧焊接工艺试验研究.结果表明,采用等离子弧焊接方法,ERCr Ni Mo-3焊材及合理的焊接工艺参数,等离子弧焊接工艺可用于Alloy 20不锈钢薄板的焊接,焊接接头各项性能均能满足要求.关键词:Alloy 20;不锈钢薄板;等离子弧焊接;......
)Abstract:Stainless die with micro-groove and micro-hole have been designed and manufactured, which has been used to study superplastic microforming of 2091Al-Li alloy by means of superplastic forming... micro-rib specimen, behavior of material could be understood well.Key words:superplasticity; microforming; extrusion; 2091Al-Li alloy......
alloy. NIEH et al [14] reported that the addition of scandium (Sc) to Al-Mg alloy resulted in the precipitation of fine Al3Sc, effectively pinning grain boundaries during recrystallization. As a result.... BAE and GHOSH [11,12] experimentally investigated cavity growth in a superplastic flow of Al-Mg alloy and suggested an improved plasticity-based model. PATANKAR and JEN [13] investigated the effect......
Study on Thermomagnetic Treatment Fe-25.5Cr-12Co Permanent Magnetic Alloy Zhen Liang1,GAO Run-sheng2,ZHU Dan-yang1,SUN Xue-yin1,SHAO Wen-zhu1,XU Ren-gen1 (1.Technology and Development Centre... Fe-25.5Cr-12Co alloy by different process of thermomagnetic treatment were investigated. It is found that magnetic properties are sensitive to parameters of thermomagnetic treatment process in magnetic......
is the theory of the characteristic crystals and points out direction of alloy design. The theory has been successfully applied to Ag–Cu alloys [1, 2] and Au–Cu alloys [3–6] in FCC structure, Ti–Al... J. Cent. South Univ. (2018) 25: 1573-1581 DOI: https://doi.org/10.1007/s11771-018-3849-x Derivation and application of concentration formula of alloy genes of DO3-type in BCC alloy systems PENG......
,Changsha 410083, P. R. China) 摘要:Three Al-Cu-Mg-Fe-Ni-Sc-Zr ingot metallurgy alloys with different compositions had been prepared. The hardness variations of cold-rolled alloy plates during annealing...(Sc, Zr) particles were improved. And the tensile strength of alloy did not improve obviously with rich iron and nicker addition. 关键词:Al-Cu-Mg-Fe-Ni alloy phase Al3(Sc; Zr) tensile property annealing......