共搜索到11270条信息,每页显示10条信息,共1127页。用时:0小时0分0秒937毫秒
glycol) is added as chelating agent. By controlling the reaction conditions such as temperature, pH value and aging time, hydroxyl ions become attached to the metal atom to form metal complexes, which......
. Defects or internal stress may contribute to the formation of the crystalline nucleus, the grain boundaries and dislocations acting as diffusion tunnels[32]. And the addition energy, stored in the form of a variety of defects including grain boundaries, dislocations, internal strain or stress, will be released during annealing process, which is found to shorten the ordering transformation time......
deformation in W-La tool pin which was a function of the FSW stress and temperature. Therefore, a new tool of a cylindrical pin with an increased pin tip diameter of 6.3 mm was used for the additional... to produce geometries and shape that reduce the net stress. After these trials, a 27.94 cm long weld run was carried out at 1000 r/min and 25mm/min. Figure 18 shows the mass change corresponding......
of the deposition of the Paleogene Suweiyi Formation and the Neogene Kuqa Formation. In this period, the maximum principal stress, oriented in the NNW-SSE direction, created two conjugate fracture... fault was reactivated by the violent collision with the subducting Indian Plate. The maximum principal stress, oriented approximately in the north-south direction, resulted in NEE-trending shear fractures......
the depth of the reinforcement layer (see Figure 4). The footing was loaded statically to a stress of 200 kPa. This load was then transformed to a dynamic load in the manner shown in Figure 5. It should..., it is also seen that when the depth of sand was beyond a certain range (i.e., H=1.7B), the curves in all the tests were relatively close to each other. In this case, the beneficial effect of the stress......
metal concentrations. Due to the absence of cell war, however, they are easily deactivated by high shear stress made by high pulp density, thus affecting the copper extractions [60-65]. Compared..., 105(3, 4): 213-221. DOI: 10.1016/ j.hydromet.2010.10.001. [53] TUPIKINA O V, MINNAAR S H, van HILLE R P, van WYK N, RAUTENBACH G F, DEW D, HARRISON S T L. Determining the effect of acid stress......
on the residual stress during selective laser melting (SLM) of metallic powder[J]. The International Journal of Advanced Manufacturing Technology, 2016, 87(1/4): 647-656. [6] UZAN N E, RATZKER B.... Microstructure, mechanical properties and residual stress of selective laser melted AlSi10Mg[J]. Journal of Materials Engineering and Performance, 2019, 28(11): 6753-6760. [47] CHEN Jing, HOU Wei......
AR062-034, and the United States Department of Energy under the Genomics: GTL program through the Virtual Institute of Microbial Stress and Survival (VIMSS; http://vimss.lbl.gov), Environmental......
. [38]Barrallier L, Fabre A, Masse J E, et al. Residual stress measurements using neutron diffraction in magnesium alloy laser welded joints[J]. Materials Science Forum, 2002, 404-407: 399-404. [39]宋刚, 刘......
J. Cent. South Univ. Technol. (2010) 17: 1058-1069 DOI: 10.1007/s11771-010-0598-x Linear manifold clustering for high dimensional data based on line manifold searching and fusing LI Gang-guo(黎刚果), WANG Zheng-zhi(王正志), WANG Xiao-min(王晓敏), NI Qing-shan(倪青山), QIANG Bo(强波) Institute of Automatio......