共搜索到16281条信息,每页显示10条信息,共1629页。用时:0小时0分0秒399毫秒
AA5xxx and AA6xxx joints was investigated by HECTOR et al [16] and reported that FSW process can join dissimilar aluminium material of higher tensile strength. KHODIR and SHIBAYANAGI [17] investigated... D65 joint is 0.97 which is lower than 1.0 and hence dissimilar joint falls under "notch brittle material" category, i.e, the joint strength is lower in notched condition than in unnotched condition......
of the dissimilar joints resumed basically to that of AA2024 base material. And the AA2024 HAZ was obviously hardened, which should be attributed to the introduced dislocations during cyclic...Tensile and cyclic deformation response of friction-stir-welded dissimilar aluminum alloy joints: Strain localization effectP.L.Niu1,2,W.Y.Li1,D.L.Chen21. State Key Laboratory of Solidification......
, the application of FSpW in industry has not been entirely successful. In this review article, the research of similar and dissimilar material joints, such as, Al/Cu, Al/Ti, Al/Mg and Al/Steel...Refill Friction Stir Spot Welding of Similar and Dissimilar Alloys:A ReviewXiao-Song Feng1,Song-Bin Li2,Li-Na Tang2,Hui-Min Wang31. Shanghai Aerospace Equipments Manufacturer Co,Ltd2. Shanghai......
Mechanical and Galvano-chemistry Property Variation within Dissimilar Metal Weld between 1Cr18Ni9Ti and 1Cr13 Stainless SteelYongtao Zhao ,Junhui Dong,Yonglin Ma,Liping Zhao and Xiaobing Pei Material... the microstructure and properties variation of the weld metal in the dissimilar stainless steels during the argon tungsten-arc welding process.Because of the existence of different materials and chemistry......
of Technology, Harbin 150001, China) Abstract: Dissimilar metals TIG welding-brazing of aluminum alloy to stainless steel was conducted using Al-Si eutectic wire with precoating special flux layer... machine. The results show that the aluminum base material is melted and mixed with the liquid filler metal to form the welded seam, which consists of α(Al) matrix and Al-Si eutectic phases......
sequentially at Al6013/Mg interface. Key words: dissimilar welding; friction stir welding; interface; material flow; intermetallic compounds; mechanical properties; aluminum 6013; magnesium 1 Introduction... between two dissimilar metals, it is better to insert the tool pin in the material with higher heat capacity and higher plasticity. Figure 1 shows the appearances of the FSW joints with different parameters......
metal(WM) lead to variation in mechanical properties within the dissimilar joint,which determines the performance of the welded structure.In the present study,appropriate filler material was used...Formation and evolution of layered structure in dissimilar welded joints between ferritic-martensitic steel and 316L stainless steel with fillersGuoliang Liu1,2,Shanwu Yang1,Jianwen Ding1,Wentuo......
distribution of friction stir welded joints between dissimilar 2024 and 1060 aluminum alloy. The experimental results show that the flow patterns of material at different locations in the weld are different... Transactions, 2001, 32A(11): 2879- 2884. [5] OUYANG J H,KOVACEVIC R. Material flow and microstructure in the friction stir butt welds of the same and dissimilar aluminum alloys[J]. Journal of Materials......
Mechanical properties of electron beam welded dissimilar joints of TC17 and Ti60 alloysChao Cheng1,2,Bingbing Yu1,Zhiyong Chen1,2,Jianrong Liu1,2,QingjiangWang1,21. Institute of Metal Research... and high cycle fatigue(HCF) properties of the welded dissimilar joints of Ti60 and TC17 titanium alloys had been investigated in this study. A significant microstructural change was observed to occur......
Dissimilar Joining of Pure Copper to Aluminum Alloy via Friction Stir WeldingFarhad Bakhtiari Argesi,Ali Shamsipur,Seyyed Ehsan MirsalehiDepartment of Mining and Metallurgical Engineering,Amirkabir University of Technology摘 要:In this study, the dissimilar friction stir welding(FSW) butt joints between aluminum alloy 5754-H114 and commercially pure......